Sits lower on driver's side.
#1
Sits lower on driver's side.
I'm trying to figure out why my truck sits about an 1 1/4" lower on the driver's side. I went around with a tape measure and checked and both the front and back of the truck sit lower than the passenger side. I actually can feel it when driving, feels like it wants to tip over when I'm turning right. Could it just be worn shocks? What else should I look for?
All four tires have the same pressure in them also.
All four tires have the same pressure in them also.
#4
No mention of if its 2WD (front springs) or 4WD (front torsion bars).
A "no" on the shocks. They do not support weight.
A very chubby girl friend could help even it out
Seriously, it takes careful measurement on a level surface to find out which end, or both, are the culprit. A sagged spring at one corner can make the whole side look low.
A "no" on the shocks. They do not support weight.
A very chubby girl friend could help even it out
Seriously, it takes careful measurement on a level surface to find out which end, or both, are the culprit. A sagged spring at one corner can make the whole side look low.
#5
#7
that dosent make sense. if the truck rolls when making a RIGHT hand turn, but is sitting lower on the LEFT hand side, then it should emulate a nascar suspension setup and take the corner better. to me it sounds like you got more then 1 problem. check your sway bar links.
Trending Topics
#8
#12
Not really. When I say check the alignment , I mean make sure they are
adjusted evenly. On the back side of the tortion bar is an adjustment bolt
that moves the adjuster arm up and down creating torque on the bar. Make sure you have the same number of threads showing through the bolt. If it's off you will see it . You can raise and lower that arm to put more torque on the bar thus raising and lowering one side or the other. If that's not the problem then something could be bent.
adjusted evenly. On the back side of the tortion bar is an adjustment bolt
that moves the adjuster arm up and down creating torque on the bar. Make sure you have the same number of threads showing through the bolt. If it's off you will see it . You can raise and lower that arm to put more torque on the bar thus raising and lowering one side or the other. If that's not the problem then something could be bent.
#13
#14
I know this is an old thread, but I just adjusted the torsion bar on my 2000 Ford F150 ext cab 4WD. It was also riding about 1.25" low on the drivers side and was noticeable. Looking under at the adjuster bolt it was clear it wasn't matching the passenger side bolt. The drivers side bolt had about .25" more threads exposed on the bottom.
I jacked up the front by placing the floor jack on the frame just behind the front wheel to get it off the ground and take most of the preload off the torsion bar. This made the bolt much easier to turn. I lubed up the bolt with a little PB blaster and used a 1/2" breaker bar and an 18mm socket. It actually moved pretty easy. The bolt had to be tightened a little more than the passenger side to get the sides to even out (about 1/8"-3/16 more). That took a couple of trys at getting the height close. It's still about .25" low, but I'm going to drive it a little to and check it again in a few days. It looks much better now.
I jacked up the front by placing the floor jack on the frame just behind the front wheel to get it off the ground and take most of the preload off the torsion bar. This made the bolt much easier to turn. I lubed up the bolt with a little PB blaster and used a 1/2" breaker bar and an 18mm socket. It actually moved pretty easy. The bolt had to be tightened a little more than the passenger side to get the sides to even out (about 1/8"-3/16 more). That took a couple of trys at getting the height close. It's still about .25" low, but I'm going to drive it a little to and check it again in a few days. It looks much better now.
Thread
Thread Starter
Forum
Replies
Last Post
x_man586
1980 - 1986 Bullnose F100, F150 & Larger F-Series Trucks
5
01-03-2014 09:10 PM
TexasGuy001
1987 - 1996 F150 & Larger F-Series Trucks
10
07-30-2007 10:48 AM