Pioneer avic install help!!
#1
04-04-2009, 04:57 PM
Join Date: Apr 2007
Posts: 46
Likes: 0
Received 0 Likes
on
0 Posts
#2
04-04-2009, 08:05 PM
Post Fiend
Join Date: May 2006
Location: Central Florida
Posts: 10,007
Likes: 0
Received 0 Likes
on
0 Posts
Radio 12v lt. green/purple + radio harness
Radio Ground black and black/lt. green - radio harness
Radio Ignition pink/black or lt. green/yellow + radio harness
Radio Illumination lt. blue/red (dimmer) + radio harness
Factory Amp Turn-on dk. green/purple + radio harness
Notes: This is the subwoofer amplifier turn on lead. The subwoofer and amp are in the driver side rear corner of the cabin. The subwoofer speaker wires are brown/orange (+), and red/black (-) at the radio harness.
Power Antenna N/A
LF Speaker +/- orange/lt. grn - lt. blue/wht +,- radio harness
RF Speaker +/- white/lt. grn - dk. green/org +,- radio harness
LR Speaker +/- gray/lt. blue - tan/yellow +,- radio harness
RR Speaker +/- orange/red - brown/pink +,- radio harness
Radio Ground black and black/lt. green - radio harness
Radio Ignition pink/black or lt. green/yellow + radio harness
Radio Illumination lt. blue/red (dimmer) + radio harness
Factory Amp Turn-on dk. green/purple + radio harness
Notes: This is the subwoofer amplifier turn on lead. The subwoofer and amp are in the driver side rear corner of the cabin. The subwoofer speaker wires are brown/orange (+), and red/black (-) at the radio harness.
Power Antenna N/A
LF Speaker +/- orange/lt. grn - lt. blue/wht +,- radio harness
RF Speaker +/- white/lt. grn - dk. green/org +,- radio harness
LR Speaker +/- gray/lt. blue - tan/yellow +,- radio harness
RR Speaker +/- orange/red - brown/pink +,- radio harness
Description
Factory amplifier integration harness (Click on part for more details)
Product Specifications
* -Factory Amplifier Integration harness
* -2 RCA plugs to mate to aftermarket radio's pre-amp outputs
* -One 24-pin power plug and one 8-pin subwoofer plug
* -A 1.5K Ohm resistor can be used on the amp-remote wire to eliminate turn-on pop.
Allows installation of an aftermarket radio using the existing factory wiring and connectors. No cutting of factory wiring is needed.
Factory amplifier integration harness (Click on part for more details)
Product Specifications
* -Factory Amplifier Integration harness
* -2 RCA plugs to mate to aftermarket radio's pre-amp outputs
* -One 24-pin power plug and one 8-pin subwoofer plug
* -A 1.5K Ohm resistor can be used on the amp-remote wire to eliminate turn-on pop.
Allows installation of an aftermarket radio using the existing factory wiring and connectors. No cutting of factory wiring is needed.
#3
04-05-2009, 08:43 AM
hey, I installed one in a 02 Explorer sport and the folks at AVIC411.com were a lot of help both with the install and with any other questions you may have.
#5
04-06-2009, 09:19 AM
Tuned
definitely check out AVIC411.com, lots of good info over there. Be careful, they are a little tough on new guys sometimes lol
Thread
Thread Starter
Forum
Replies
Last Post
PostRelease
2009 - 2014 F150
0
11-02-2009 01:51 PM
Pittsburgh-05HD
Audio & Video Systems, Navigation, Satellite Radio & Mobile Electronics
1
07-05-2007 11:43 AM
trojanman1
Audio & Video Systems, Navigation, Satellite Radio & Mobile Electronics
133
08-22-2006 09:53 PM
