HELP P1316 code & Runs Rough??
#1
HELP P1316 code & Runs Rough??
On sat. morning I drove appx. 1/2 mi. parked, came out 5 min. later and started my 2001 F350 SD Diesel W/75,000 mi. and it was running rough and the SES light was on. I changed fuel filt. in the fall and maintain it well.
Pulled the code with my OTC Genisys and came up with P1316 Ignition Diagnostic Monitor Codes Detected.
My Alldata dosen't go to 2001 and I have no other info for this truck. I'm thinking I've got a injector gone bad.
Any one have any exp. with this that can guide me??
TIA
Tommy
Pulled the code with my OTC Genisys and came up with P1316 Ignition Diagnostic Monitor Codes Detected.
My Alldata dosen't go to 2001 and I have no other info for this truck. I'm thinking I've got a injector gone bad.
Any one have any exp. with this that can guide me??
TIA
Tommy
Last edited by racingtom; 04-02-2007 at 07:13 PM.
#2
P1316 is a generic IDM code. It means that you have more codes stored inside the IDM itself. The way to retrieve them is to run an injector buzz test.
Since I've never used the Genisys, I have no idea if it's capable of that. Quite a few PSD owners as well as myself use Autoenginuity, which can run a buzz tests and pull IDM codes in a few seconds.
If you can't pull the IDM codes at the moment, your best best is to first check the UVC harnesses. They are located in the middle of each valve cover and each face the valley of the engine. You'll either have chaffed wires from a failed harness, or the clip underneath the valve cover popped off. For that you'll have to take the valve covers off and reconnect. They come off surprisingly easy.
Hope this helps.
Since I've never used the Genisys, I have no idea if it's capable of that. Quite a few PSD owners as well as myself use Autoenginuity, which can run a buzz tests and pull IDM codes in a few seconds.
If you can't pull the IDM codes at the moment, your best best is to first check the UVC harnesses. They are located in the middle of each valve cover and each face the valley of the engine. You'll either have chaffed wires from a failed harness, or the clip underneath the valve cover popped off. For that you'll have to take the valve covers off and reconnect. They come off surprisingly easy.
Hope this helps.
#4
Originally Posted by Pocket
If you can't pull the IDM codes at the moment, your best best is to first check the UVC harnesses. They are located in the middle of each valve cover and each face the valley of the engine. You'll either have chaffed wires from a failed harness, or the clip underneath the valve cover popped off. For that you'll have to take the valve covers off and reconnect. They come off surprisingly easy.
Hope this helps.
#5
Well I started my truck this morning for my drive to work (appx 8 mi. drive) and it was running fine with no SES light, at arround 6 mi. here it goes again missfiring and SES on.
So after work I decided to pull the valve cover's and of course the second one I pulled
the connector was backed off, while I had the both cover's off I secured both harnesses inside the cover's. Only took about 2 hrs. . Started good and road tested, runs great.
Thanks for the help guy's.
Tommy
So after work I decided to pull the valve cover's and of course the second one I pulled
the connector was backed off, while I had the both cover's off I secured both harnesses inside the cover's. Only took about 2 hrs. . Started good and road tested, runs great.
Thanks for the help guy's.
Tommy
#7
Trending Topics
#8
Thread
Thread Starter
Forum
Replies
Last Post
IQof3
1999 - 2003 7.3L Power Stroke Diesel
1
01-08-2012 07:25 PM