80-86 parts, 92-97 parts alot
#1
80-86 parts, 92-97 parts alot
Category: Accessories
Price: $30000
Private or Vendor Listing: Private Listing
Part fits (you may select multiples): Fit, S2000
Item Condition: OH
Shipping Information: Item can be shipped
Engine: Part suitable for gas truck
Name is Matt,
Located in Cincinnati Ohio
Pm me or reply to this
Small Parts can be shipped, will ship bigger stuff also, both on the buyers dime.
Trucks the parts came from:
have an 86 f250 2wd reg cab long bed rolling chassis minus fuel system. has a carb 460 with a c6 behind it, has the big studs for the wheel studs, it is the heavy Gvwr.
motor runs flawlessly and trans shifts awesome, truck has 50k original miles on it, we bought it for its body and don't wanna junk the power-train. will put a link of the build thread so you can get an idea of how the 86 was taken care of.https://www.ford-trucks.com/forums/1...-xl-build.html
next is a 85 f250 2wd reg cab long bed red in color NO AC. has a 351 HO and c6 trans. Not a clue what condition the trans is in, and the 351 needs a rebuild, i believe the bottom end is fried. pretty sure odometer is rolled and it reads around 19k. So truck does not run and drive, has been sitting for 10 years
some miscellaneous parts from the uncles 84 250 with 351 and 4 spd No AC. very low amount of parts from this, power train was used in the rebuild of the truck as was the whole chassis. interior is fried blue, which we would like to keep the bigger pieces, and body was rotted fairly bad, again see build thread posted above for condition this truck was in.
And lastly is a 97 hd xl AC 250 reg cab long bed 4x4 460 5 spd. Seat belts sold already. Transmission, steering wheel and shroud and other parts related to swapping an auto out for manual are NOT for sale, because i am putting the 5sp in my 97, but parts from my 97 will be available such as the e4od, pedals, pcm, trans hump, cross member......
cab is spoken for off this truck.
has grey interior parts available. dash is good, seat is junk. bed is freaking beat to death. not sure what interest will be but if ya see something, ask!!!
prices I have no clue on really since not sure what interest will be.
Will say 1200 for 86 rolling chassis, interior parts 15-50. body parts 60-90, grille pices10-20-30, random pieces ........ depends what it is.... just ask, trucks will be going to scrap when spring rolls around.
The fenders off the 85 are really nice, the core support is starting to rot but i believe a sandblasting and it is solid. cab floor on 85 is starting to go , doors are starting also, bedsides are decent but drivers side is starting the rust over rear wheel well.
the 86 chassis is in great structural form.
the 97 is in good structural shape, fenders are nice and core support is rotted.
here are some pics
The 86 chassis:
The 85 f250 red:
The random left overs from 84visor and hood not for sale)
only have pass side headlight bezel from 84 and grille upper and lower. the drive side bezel has broken tabs
unfortunately only have 3 of these hubcaps but they are all in perfect shape
Lastly the 97 f250 4x4:
#2
I need a couple frame crossmembers. The one that the cab sits on. Do you have one of those in good shape. And the core support mounts i need a pair thats not rusted out.
#3
the 85 and 97 may have them in good shape, but I currently dont have access to them and am not taking cab offs for crossmembers, now when the cab comes off the 97 i will check for ya!!! as for the core support ones, i will check also when trucks come apart
#5
we had to take the one that holds the back of the cab, and the two front body mount brackets from the 86 rolling chassis for the 84s, cause the 84s were rotted out.
I know the core support ones are spiffy clean on that frame though
I know the core support ones are spiffy clean on that frame though
Trending Topics
#12
yes it is at the house, it is the late 85-86 style with the din style radio opening, not sure on condition of the tabs but can check