Michigan Chapter Join Chapter, Leader: Toyman

Need help with 7.3L powerstroke. anyone have scanner

Thread Tools
 
Search this Thread
 
  #1  
Old 05-22-2011, 05:04 PM
Milwaukee1979F150's Avatar
Milwaukee1979F150
Milwaukee1979F150 is offline
Posting Guru
Thread Starter
Join Date: Jan 2008
Location: Trenton, MI
Posts: 2,408
Likes: 0
Received 0 Likes on 0 Posts
Need help with 7.3L powerstroke. anyone have scanner

I am in Trenton

I bought 00 F350 7.3L so have issues with run rough and hard start.

Engine light is ON so I tried my scanner it say nothing codes on but there engine light ON.

PO replace so many parts on engine that confused me. On quick rev there TONS blue smoke but if you do slow rev almost no smoke or little blue smoke.

Very hard start. Have 1 bad glow plugs.
 
  #2  
Old 05-26-2011, 12:08 AM
jimmyv13's Avatar
jimmyv13
jimmyv13 is offline
Posting Guru
Join Date: Mar 2010
Location: West Bloomfield, MI
Posts: 1,629
Likes: 0
Received 1 Like on 1 Post
I have an SCT, how far away are we? I'm fairly new to the area.
 
  #3  
Old 05-26-2011, 07:01 AM
craftsmangary's Avatar
craftsmangary
craftsmangary is offline
More Turbo
Join Date: Jun 2009
Location: Michigan
Posts: 566
Received 49 Likes on 36 Posts
Is it drivable? What has been done to it? How many miles? If the CEL is on you have codes. If the PO was throwing parts at it he must have been guessing, and that gets expensive and usually causes more problems.
If you can get it to me I have scanners that can do a buzz test and cylinder contriburion test, and I'm in South Lyon
 
  #4  
Old 05-26-2011, 07:59 AM
SDElwood's Avatar
SDElwood
SDElwood is offline
Hotshot
Join Date: Apr 2003
Location: Savannah, GA
Posts: 14,676
Received 588 Likes on 319 Posts
Makes me wonder if the valve cover wiring harness has some goofs. Not too hard to check and it is a beer drinking sport.
 
  #5  
Old 05-26-2011, 08:52 AM
Milwaukee1979F150's Avatar
Milwaukee1979F150
Milwaukee1979F150 is offline
Posting Guru
Thread Starter
Join Date: Jan 2008
Location: Trenton, MI
Posts: 2,408
Likes: 0
Received 0 Likes on 0 Posts
I end order AE scanner but everybody live far away.

I don't trust this truck to be on highway. It will drive but sometime you push more on gas it POUR BLACK smoke.

It have very bad hesitance and shake when Rev.

It only had 210K miles. Everybody told me it low compression I don't believe because it run too good at idle. Have 8 dead glow plugs.


CEL is on when crank and run. I am going check that truck with AE scanner today. Just got AE last night.
 
  #6  
Old 05-26-2011, 09:11 AM
craftsmangary's Avatar
craftsmangary
craftsmangary is offline
More Turbo
Join Date: Jun 2009
Location: Michigan
Posts: 566
Received 49 Likes on 36 Posts
Was a compression test done with a guage, if not it a guess......... and most times a guess is wrong. With 210k the original injectors will be near the end of there life cycle. Post the codes you get.
 
  #7  
Old 05-26-2011, 09:17 AM
Milwaukee1979F150's Avatar
Milwaukee1979F150
Milwaukee1979F150 is offline
Posting Guru
Thread Starter
Join Date: Jan 2008
Location: Trenton, MI
Posts: 2,408
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by craftsmangary
Was a compression test done with a guage, if not it a guess......... and most times a guess is wrong. With 210k the original injectors will be near the end of there life cycle. Post the codes you get.

It guess because it idle very good for 210K miles. But it misfire shake when in gear.


Will go get codes in couple hours. Truck in Monroe.
 
  #8  
Old 05-26-2011, 01:27 PM
Milwaukee1979F150's Avatar
Milwaukee1979F150
Milwaukee1979F150 is offline
Posting Guru
Thread Starter
Join Date: Jan 2008
Location: Trenton, MI
Posts: 2,408
Likes: 0
Received 0 Likes on 0 Posts
Got new codes again

P1280
P1293
P1284

Can't rev anymore or it blow smoke badly.

I look at ICP connector it been cover in oil.
 
  #9  
Old 12-16-2011, 09:49 AM
tlb22's Avatar
tlb22
tlb22 is offline
New User
Join Date: Dec 2011
Posts: 1
Likes: 0
Received 0 Likes on 0 Posts
I have a 2003 F350 dually i bought off a friend. it does the exact same thing. if i start it everyday it is ok, but just ok, still have to run for a while before it runs good. if you dont let it warm up for a long time and you try to drive it, it viberates very bad at times. no matter how hard you press the peddle the responce can very from not much when cold, to normal when ran a while. a while being 20 min, maybe longer. I used my dads edge programmer to adjust increase HP and it did help, but not enough. I unplugged the injector harness one at a time while running and when i unplugged the passenger side it died, so i knew my rough "running/idle" is mostly from the driver side. i replaced the injector harness as they are known to burn up. Still rough run/idle. it appears to me that i have an injector or multiple injectors bad on the drivers side. given i have 260,000 miles they are all probably limping along. given the rough starts i would guess injector O rings are bad allowing fuel to leak off. O rings may by time, but limited time. I hate to purchase 8 new injectors. any one have any advice? used to be able to purchase rebuild kits for them, can you still and where? anyone have any experience with aftermarket injectors? will an injector buzz test confirm my thoughts about needing injectors 100%? I will pass along anything i discover. my last thought is, can a person take the valve cover off and unplug one injector at a time to see if there is a performance difference? i know oil will go everywhere, but does anyone see a negative affect this would have. then i could pin point the exact injectors and just replace them for the time being, before i replace them all. test like spark plugs on a gas car. if no performace difference when unplugged then that one(s) are bad.
 
  #10  
Old 12-16-2011, 10:30 AM
Milwaukee1979F150's Avatar
Milwaukee1979F150
Milwaukee1979F150 is offline
Posting Guru
Thread Starter
Join Date: Jan 2008
Location: Trenton, MI
Posts: 2,408
Likes: 0
Received 0 Likes on 0 Posts
Mine had bad PCM, 6 bad injectors. They work great when it warm up. Cold it still miss and rough. Now it running great but tiny rough but it Michigan winter here.


Cheapest reman injectors I trust. Riffraff Diesel: Stock Rebuilt Injectors
 
  #11  
Old 12-20-2011, 12:10 PM
officer131's Avatar
officer131
officer131 is offline
Posting Guru
Join Date: Dec 2007
Location: Metro Detroit, MI.
Posts: 1,265
Likes: 0
Received 0 Likes on 0 Posts
P1280 ICP Circuit Out of Range Low.
p1293 High Side Open Bank No. 1 (Right)
p1284 ICP Failure - Aborts KOER/CCT Test



sorry came into this thread just now. These are coddes from guzzles website. Welcome to guzzle's Diagnostic Trouble Code list Web Page
 
  #12  
Old 12-22-2011, 12:50 PM
RickBraden's Avatar
RickBraden
RickBraden is offline
Tuned

Join Date: Sep 2010
Location: South of Detroit
Posts: 287
Received 0 Likes on 0 Posts
I live very closr to you

I'm within 5-6 miles of you. I have Scangauge 2, Edge Evolution CTS, & Auto Enginuity for the Ford stuff. Let me know if I can help you out. I'd be happy to helip you out if I can.
 
  #13  
Old 03-10-2015, 01:25 PM
SDElwood's Avatar
SDElwood
SDElwood is offline
Hotshot
Join Date: Apr 2003
Location: Savannah, GA
Posts: 14,676
Received 588 Likes on 319 Posts
You hiding in here with the beer Rich?
 
  #14  
Old 03-10-2015, 03:13 PM
Toyman's Avatar
Toyman
Toyman is offline
FTE Chapter Leader

Join Date: Feb 2004
Location: Wayland, MI
Posts: 14,829
Likes: 0
Received 38 Likes on 31 Posts
No but I've been wondering where Milwaukee has been lately......
 
  #15  
Old 03-10-2015, 03:14 PM
SDElwood's Avatar
SDElwood
SDElwood is offline
Hotshot
Join Date: Apr 2003
Location: Savannah, GA
Posts: 14,676
Received 588 Likes on 319 Posts
Liar! I found the beer.
 


Quick Reply: Need help with 7.3L powerstroke. anyone have scanner



All times are GMT -5. The time now is 11:44 PM.