Send me a picture of you glove box door to my email. jrkeesling@gmail.com

Hi - I'm not sure what you've got left by now but I'm looking for a few things:

1) 48-52 F1 bench seat
2) 48-52 F1 spindle/steering arm (connects spindle to drag link)
3) 48-52 F2 lower shock mounts (to accommodate my 9" swap)

Let me know what you've got and what I'll owe. Thanks in advance.

-Jon

Jon

Send me an email at jrkeesling@gmail.com. I check it more frequently and Photos send better.
I should have everything you need.
Thanks!

Looking for an ash tray for a '51 F-6; also need a PTO for same, with the T-98 trans.

Greetings. New to site.
Have a '49 F6 COE. Looking for right side running board, and the top half of the oil bath air cleaner, plus a few more parts as time goes on including drivers side door.


Thanks.

It turns out that I still need these parts. Does anyone have a any ideas?
https://www.ford-trucks.com/forums/1...l#post12135809

Edit 3/1/15: Found the parts I needed at Little Dearborn and on eBay. Use the 1939-1948 Ford Car part numbers as they are the same as F2 pickup truck parts.

https://cimg3.ibsrv.net/gimg/www.for...0297ed2189.jpg


https://cimg4.ibsrv.net/gimg/www.for...7d5085f334.jpg

looking for 48-52 front axle complete and 48-52 rear springs

I am also looking for a 48-52 seat with mounting brackets.

Walt I have the old seat out of my 49f5 you could have for free. Where are you located?

Brian,

Great! I am in southern Nevada, close to Las Vegas. Where are you?

Walt

Bonney Lake Wa. Which is about 20 miles from Tacoma

Air Deflector
 

Greetings,
I am looking for an air deflector for a six cyl engine for a 1950 F-1.

Any luck?

Thanks,
lm987

007Brian, if you come to the Washington Chapter meeting on the 21st I can pick that seat up off of you for Walt. I get down to California on a fairly regular basis and perhaps we can relay it to him.

I should have an ash try and a PTO. What is your email and I will get photos for you.

I don't think I have a running board or a door. COE parts are a little on the tough side to find. Are the COE air cleaner tops the same as a conventional truck?

Are you referring to the deflector that covers the front portion of the intake/exhaust manifolds?

I have an axle without hubs and I have rear springs.

fifty-two,

Thanks, I am attempting to work with a guy in CA (I am in southern Nevada) to get what I need. I will keep your offer in-mind and let you know.

Thanks again,

Walt

Where is the meeting Mark?

Washington Chapter FTE
 

Hey Brian, we have a meet-up once a month, usually in the Tacoma area.

https://www.ford-trucks.com/forums/1...et-thread.html

Go to the end of the thread, it will tell you where the meeting is or feel free to ask Gruesomejeans. Please, feel free to come and meet the other members!

Good evening fifty-two_f1,

I just sent an email re: inner fenders. I hope that is ok.

Best regards,
Dave

1949 wing windows with glass channels for front and bottom of side glass, ? any shape as I have to cut them for my chop, Thanks

Send me an email to jrkeesling@gmail.com. I should have what you need. I think I have original channels as well. So you need the complete wing window assemblies with glass?

yes complete assemblys but don't need glass as I will have to modify them and make new glass for the chop top Thanks Mike

looking for a steering wheel, double mount antenna, original brake lights, cab light, heater switch for non deluxe model. not sure if you have any. Thanks

Wanted: 1948-52 F1 Front leaf springs
I am helping a friend in NE PA with a project, we need a set of F1 front springs, u-bolt and u-bolt mounting plates. Anyone?

I got mine from Posies in Hummelstown, PA (POSIES Rods and Customs). Their DualFlex will give you a 2-3" drop without doing anything else. They have other options too. Suggest calling them. They were most helpful.

Pete, thanks for reply, but I should have noted that we are looking for some used springs just to get his truck to roll.

I may have what you need, if you are still looking. I'm in Buffalo NY. Drop me a message.

John

Please add a few pictures of your Magic Air emblems & decals. My '50's got the Magic Air heater. Thanks so much!

WANTED:
I am looking for the F-1 stainless steel trim for front windshield for a 5-star cab.
Thanks,
Walt

I have found the stainless windshield trim, thanks!

Hi, I'm looking for an air cleaner for my 51 F3, 226 H.
Thanks

Walt, sorry I didn't respond sooner! I guess I have been away from FTE too long. School consumes most of my time.

Tim, Ill take a look this weekend I think I have one left.

HOW MUCH FOR THE 1950 F1 8BA ENGINE IF ITS NOT SOLD AND WILL U SHIP TO CHICAGO? IAM ALSO LOOKING FOR A 4 SPEED TRANSMISSION CASE FOR A 1950 F1.

The engine is sold, I have another but the block is cracked. It can be fixed, but that is your call. Do you just need the case or the whole transmission?

need 2 doors 1950 f1

Send me an email at jrkeesling@gmail.com and I will send you some photos.

Need the exhaust heat riser counter weight off a 226 if you have it!? Also a set of f2/3 tailgate hinges, I believe they are slightly larger than the f1s. Thanks!!

Fifty Two,
I'm looking for the support strap for the air cleaner on a 226, I also need a passenger side vent window, frame with glass would be great for a 51' F-3
Thanks